CNET CBR-980 Manual do Utilizador Página 1

1 CBR-980 Wireless-N Broadband Router User Manual Version 1.0 (Dec, 2009)

10 2.2 Connecting to CBR-980 by Web Browser After the network connection is built, the next step what you should do is setup the router with prop

100 5.6 Log & Status The category provides Network Config and Event Log status for users to know the operation status. 5.6.1 Network Conf

101 5.6.2 Event Log You could enable the event log feature here. Item Description Enable Log You may choose to enable Event Log or not Syst

102 Apply & Cancel Click on Apply button to add the settings into the list table. Click on Cancel button to clean the setting on this page. *Th

103 Chapter 6 DDNS Account Setup You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it wil

104 【Step 3】 When the below window appears, you already finish the registration. Please check your E-mail box, and you will receive an e-mail from

105 【Step 4】 Please open the email sent from DynDNS. Click on the link to confirm your account.

106 【Step 5】 Please click on login. 【Step 6】 Please click on My Services under the Account Summary for the linkage. 【Step 7】 Please click on Ad

107 【Step 8】 Please click on Add Dynamic DNS Host. 【Step 9】 1. Please input the account you applied. 2. Please select the hostname preferred at

108 【Step 10】 When the below window appears, it means your hostname is created. 1 2 3

109 Chapter 7 Q & A 7.1 Installation 1. Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is insta

11 2.2.1 Windows 95/98/ME 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-c

110 7.3 IP Address 1. Q: What is the default IP address of the router for LAN port? A: The default IP address is 192.168.1.1 with subnet mask 255.

111 displayed on the screen. What do I need to do? A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate" feat

112 A: Periodically, a new Flash Code is available for 11n Broadband Router on your product supplier’s website. Ideally, you should update 11n Broad

113 7.6 Wireless LAN 1. Q: Why couldn’t my wireless notebook work on-line after checking? A: Generally, Wireless networks can sometimes be very

114 2. Q: My PC can’t locate the Wireless Access Point. A: Check the following:  Your PC is set to Infrastructure Mode. (Access Points are always

115 A: The Wireless Router processes the data passing through it, so it is not transparent. Use the Special Application feature to allow the use of

116 7.8 Others 1. Q: Why can’t I receive corrupted FTP downloads? A: If you are experiencing corrupted files when you download a file with your FT

12

13 2.2.2 Windows 2000 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click

14

15 2.2.3 Windows XP 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Double-click N

16

17 2.2.4 Windows Vista 1. Click ‘Start’ button (it should be located at lower-left corner of your computer), then click control panel. Click View

18

19 2.2.5 Router IP Address Lookup After the IP address setup was completed, please clicks ‘start’  ‘run’ at the bottom-lower corner of your desktop

2 Table of Contents TABLE OF CONTENTS ... 2PR

20 2.2.6 Connect the Wireless Router’s management Interface by Web Browser After your computer obtained an IP address from wireless router,

21 NOTE: If you can’t see the web management interface, and you’re being prompted to input user name and password again, it means you

22 Chapter 3 One Button Setup Configuration CBR-980 “One Button Setup” will help you to setup the basic setting of the wireless router with simplify

23 Item Description Time Zone Select Press button to choose a time zone of the location you live from the drop-down list. Change Password Input

24 Chapter 4 Quick Setup Configuration There are two way to connect to CBR-980 setup page. 1. Please open your Internet browser, for example like

25 2. Click “Internet Gateway Device” to enter the login page

26 4.1 Step Setup Click on Step Setup in the left screen of the main menu, and click “Step Setup”, then click “Next” to start configure your

27 4.1.2 LAN Interface Setup Item Description Device Name Fill in the name for the wireless router IP Address The wireless router IP address

28 4.1.3.2 WAN Interface – Ethernet Port If you are using an Ethernet cable to connect the Internet, please select Ethernet port.

29

3 5.1.1.2 WAN Interface – Ethernet Port ... 425.1.1.3 WAN Interface – W

30 4.1.3.3 WAN Access Type – WiMAX If you are using WiMAX as the WAN Type, please select WiMAX and fill in the required information as follows to di

31 You can see a list of available Wireless networks. Select you preferred one to connect and the Encryption type form the drop-down list. 4.1.3

32 automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none

33 4.1.3.6 WAN Access Type – Dynamic IP Choose Dynamic IP to obtain IP address information automatically from your ISP. Select this option if your

34 4.1.3.7 WAN Access Type – PPPoE This option is typically used for DSL services. Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP

35 4.1.3.8 WAN Access Type -- PPTP This option is typically used for DSL services. Some DSL service providers supply a special DSL modem. This kind

36 Click on Next button to go on next setting page. 4.1.4 Wireless Setup First step is to name your SSID, and the default value is Download Serve

37 4.1.4.1 Wireless Security Setup The security function is provided to prevent the connection requests from unauthorized wireless clients. As the

38 Item Description Key Length There are two types of WEP key length: 64-bit and 128-bit. Using ‘128-bit’ is more safety than ’64-bit’, but data tra

39 4.2 Basic Step Complete The Basic Setup has been completed successfully when you see this screen. The system will be rebooted automatical

4 7.7 Support ... 1157.8 Others ..

40 Chapter 5 Advanced Configuration This chapter describes how to setup the access the router through the web browser. Please be noted that in ord

41 5.1.1.1 WAN Interface – 3.5G (HSDPA/UMTS) If you are using HSDPA/UMTS (3.5G connection) as the WAN Type, please select 3.5G USB Dongle. At this

42 5.1.1.2 WAN Interface – Ethernet Port If you are using an Ethernet cable to connect the Internet, please select Ethernet port.

43 5.1.1.3 WAN Interface – WiMAX If you are using WiMAX as the WAN Type, please select WiMAX and fill in the required information as follows to dire

44 You can see a list of available Wireless networks. Select you preferred one to connect and the Encryption type form the drop-down list.

45 5.1.1.5 WAN Access Type – Static IP If you applied for a Static IP connection type from ISP, please follow the steps to set up your WAN connecti

46 Item Description IP Address Please enter the IP address which is provided by your ISP. If you don’t have it, please contact your ISP. Subnet Mask

47 5.1.1.6 WAN Access -- Dynamic IP If your WAN access type is Dynamic IP, please complete the settings as following instructions.

48 Item Description Host Name The host name is optional; but if your ISP requires you to input a specific host name, please put it in, for example,

49 5.1.1.7 WAN Access Type -- PPPoE If you applied for a PPPoE connection type from ISP, please follow the steps to set up your WAN connection.

5 Preface About This Manual Thank you for purchasing the CBR-980 Wireless-N Broadband Router. This User’s Manual is intended for audience with basic

50

51 Item Description User Name Input your user name supplied by ISP. If you don’t know, please check with your ISP. Password Input your Password supp

52 Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. Enable IGMP

53

54 Item Description IP Address Input your IP Address supplied by ISP. If you don’t know, please check with your ISP. Subnet Mask Input Subnet Mask,

55 existed. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. En

56 Item Description IP Address The default IP address is 192.168.1.1 Subnet Mask Please enter the Subnet Mask address Default Gateway Please e

57 5.1.3 Dynamic DNS Setting You can assign a fixed host and domain name to a dynamic Internet IP address. Each time the router boots up, it will r

58 ODS, Regfish embedded in CBR-980. User Name/Email User name is used as an identity to login Dynamic-DNS service. Password/Key Password is appli

59 5.2.1 Wireless Basic Settings The Wireless Basic Settings include Band, Mode, SSID, Channel Number and other wireless settings.

6 Chapter 1 Introduction 1.1 About CBR-980 CBR-980 is not only a Wireless-N Router, It also equips with two USB 2.0 hosts to provides users with

60 Item Description Disable Wireless LAN Interface Turn off the wireless service. Band Please select the frequency. It has 6 options: 2.4 G

61 5.2.1.1 Multiple APs Multiple APs provides users another 4 different SSIDs for connection. Each SSID could be set with different data rate, WMM a

62 Example: When users enable the Universal Repeater to connect to the upper level device, please fill in the upper level device’s channel and SSID.

63 Item Description Fragment Threshold To identify the maxima length of packet, the over length packet will be fragmentized. The allowed range is

64 extension to IEEE 802.11 that provides wireless access-point communications among multivendor systems. Protection Please select to enable wireles

65 802.1x Authentication: It is a safety system by using authentication to protect your wireless network. 2. - Enterprise (RADIUS): Please

66 3. Apply Change & Reset: Click on ‘Apply Changes’ to save setting data. Or click ‘Reset’ to reset all the input data. 5.2.4 Wireless Acce

67 (1) Here is the example. Please select Deny Listed in Wireless Access Control Mode first, and then fill in the MAC address what you plan to bloc

68 5.2.5 WDS Settings When selected in the Basic Settings page and enabled here, Wireless Distribution System (WDS) enables the router to be use

69 The WDS explanation as the following picture. *Please follow the below instructions to setup the WDS connection. (1) Please check the MAC a

7 1.4 Getting to Know CBR-980 The front view of CBR-980 Status LED Indicator Solid Flashing POWER Operation OK

70 (2) Set the connection mode to “AP+WDS” from “Wireless Basic Setting”, and then select the channel number(in this example is “11”). Click Appl

71 (3) Enable WDS function from the page – “WDS Setting”, and then fill in the upper level device MAC address. Click Apply Changes to save the set

72 (4) The WDS AP List will show the WDS device MAC address after reboot.

73 (5) Set “Broadcast SSID” to disable from page “Wireless Basic Setting”. (6) Go to the upper level device WDS setting page and fill in the MAC a

74 (7) You will receive an IP address from the upper lever device. Please input the MAC address of this router.

75 5.2.6 WPS This page allows user to change the setting for WPS (Wi-Fi Protected Setup). Using this feature could let your wireless client atomica

76 When users select a specific model on wireless base station, the clients can connect to the base by selecting the same model. The connection proc

77 (2) Click OK to start WPS process. (3) Open the configuration page of the wireless card. Click the Wi-Fi Protect Setup, and then click PBC t

78 (5) The USB dongle will receive the connection information from wireless router if the dongle has connected to the wireless router successfully

79 (1.) Get the WPS PIN number from wireless card and write it down. * Start PIN: (2) Fill in the PIN number which from the wireless card in CBR-

8 1.4.1 Product Appearance Power Receptor Adapter, Input:90-240Vac, Output: 5V/ 1.2A Reset Button Press “Reset” button over 10 seconds. When sta

80 (3) Click OK to starts process. (4) Click PIN to start the WPS process with the wireless router.

81 (5) Click No, then USB Dongle will select AP automatically. (6) WPS is in processing.

82 (7) The following page shows the wireless card has already connected to the wireless router.

83 5.3 NAT 5.3.1 Visual Server The Virtual Server feature allows users to create Virtual Servers by re-directing a particular range of service p

84 *Please find the following figure to know that what the virtual server is. The web server is located on 192.168.1.100, forwarding port is 80, a

85 Item Description Enable DMZ It will enable the DMZ service if you select it. DMZ Host IP Address Please enter the specific IP address for DMZ

86 technologies. The primary goal of QoS is to provide priority including dedicated bandwidth, controlled jitter and latency (required by some real-t

87 Automatic Downlink Speed Click the checkbox to manage downlink speed automatically. Manual Downlink Speed Input the number of downlink speed. Ad

88 Item Description Enable Port Filtering Please select Enable Port Filtering to filter ports. Port Range Please enter the port number that needs t

89 Item Description Enable IP Filtering Please select Enable IP Filtering to filter IP addresses. Local IP Address Please enter the IP address th

9 Antenna Internal x 1, External x 1 (detachable) Peak Gain of the antenna 2dBi@ 2.45GHz Transmitted Power IEEE 802.11b: 19dBm +/- 2.0dBm (typical)

90 Item Description Enable MAC Filtering Please select Enable MAC Filtering to filter MAC addresses MAC Address Please enter the MAC address that

91 Item Description Enable URL Filtering Please select Enable MAC Filtering to filter MAC addresses URL Address Please enter the MAC address that

92 5.5.1 Change Password Users can set or change the administrator’s password in this section. Click on Apply Changes to save the setting data

93 Notes: Do not power off the device while the firmware is being upgraded Caution: To prevent that firmware upgrading is interrupted by other w

94 (1) Click Save a. Save Configuration (2) Please click “Save” to save the configuration to your computer. Reset to default. Save to compute

95 (3) Select the location which you want to save file, then click Save. (1) Click Browser b. Load configuration file (2) Select configura

96 (3) Click Upload to upload configuration file to CBR-980. (4) After 90 seconds, CBR-980 will reboot automatically. 1. Please click Reset

97 (2) Please click OK to start reload factory default setting to CBR-980. (3) After 90 seconds, CBR-980 will reboot automatically. 5.5.4 Tim

98 Item Description Current Time Users can input the time manually. Time Zone Select Please select the time zone. Enable NTP client update Plea

99 Select to enable or disable this function. *Enable/Disable UPnP 5.5.6 Language Setting CBR-980 provides users with 12 languages to choose. U