CNET CWR-854 Guia do Utilizador

1 CWR-854 54Mbps Wireless-G Router User’s Guide

4. Select Obtain an IP address automatically. Once the new window appears, click the OK button. Click the OK button again to complete the PC configu

3 Configuring this Wireless-G Router In this chapter, it describes how to use the web management tool, a web browser-based utility that allows you t

3.1.1 Time Zone Settings The first step in Setup Wizard is Time Zone Settings. Users can synchronize the local clock to an available NTP server. You

- IP Address: Enter IP address for this Wireless-G Router. - Subnet Mask: Enter the subnet mask for this Wireless-G Router. - Cancel: To skip the

- Operating Band: 802.11B/G, 802.11G or 802.11B - Operating Mode: AP, Client, WDS, and AP+WDS. - Network type: when operating mode is “Client” mod

- IP Address: Enter IP address for this Wireless-G Router. - Subnet Mask: Enter the subnet mask for this Wireless-G Router. - Default Gateway: En

- WAN Access Type: select the Static IP connection - IP Address: this is the IP address that your ISP has given you. - Subnet Mask: enter the subn

- WAN Access Type: select the DHCP Client connection - Attain DNS Automatically: enable to attain DNS from your ISP automatically. - Set DNS Manua

- WAN Access Type: select the PPPoE connection - User Name: enter the User Name provided by your ISP - Password: enter the Password provided by yo

in the WAN port. - Enable UPnP: It allows to enable or disable uPNP feature here. After you enable the uPNP feature, all client systems that support

21 INTRODUCTION...

- MTU Size: MTU is the Maximum Transmission Unit. It specifies the largest packet size permitted for Internet transmission. Keep the default setting,

- Mode: This Wireless-G Router supports four operating modes: AP, client, WDS, and AP+WDS. - Network Type: when operating mode is Client mode, users

- Refresh: Click on “Refresh” button to show the latest information. - Close: Click on “Close” button to close this window. 3.4.2 Advanced Settin

23Threshold value to split the packet. The value can be set from 256 to 2346. The default value is 2346. - RTS Threshold: RTS Threshold is a mechani

- Encryption: “None” means no encryption being selected. Users can enable the 802.1x Authentication and set the RADIUS server authentication parame

- Encryption: Select “WEP” (Wired Equivalent Privacy) encryption type. - Set WEP Key: Only valid if not select “Use 802.1x Authentication” is not

- Key Length: You can choose either 64-bit or 128-bit as the encryption key. - Key Format: You can select hexadecimal or ASCII mode as the format o

27

- Encryption: “WPA” stands for Wi-Fi Protected Access. There are three encryption modes – TKIP, AES and Mixed.  TKIP: Temporal Key Integrity Proto

“Delete Selected” button. - Wireless Access Control Mode: There are three types of access control options:  Disable: disable this control feat

1 Introduction Installing Your Router In this chapter, you’ll learn how to connect your router. System Requirements ․One or more PCs (desktop or note

set these Wireless-G Routers in the same channel and set MAC address of all other Wireless-G Routers which you want to communicate with in the table a

- Show Client button: A table shows the assigned IP address, MAC address and time expired for each DHCP leased client. 3.5 Firewall 3.5.1 IP Filter

- Delete All: Allow user to delete all Local IP Address in the Current Filter Table. - Reset: Click on “Reset” to undo your changes. - Help: To req

- Enable MAC Filtering: Enable the MAC Filtering function. - MAC Address: Enter the MAC Address that you want to block accessing the Internet. -

- Enable IPSec VPN: to enable IPSec VPN function. - Enable NAT Traversal: enable this function to detect NAT gateways between IIPSec hosts and to n

When you click on the Edit button, the VPN Setup window will display as below: - Enable Tunnel 1: Enable the IPSec VPN tunnel. - Connection Name:

36- Remote Secure Gateway: Enter remote site gateway. - Remote IP Address/Network: Enter remote site IP Address (for Single Address) or IP network

Phase 1 - Negotiation Mode: This negotiation is a main process to build a VPN connection in phase 1. - Encryption Algorithm: There are two encrypt

- Help: To request help information. 3.7 Advanced 3.7.1 Port Forwarding The Port Forwarding allows you to re-direct a particular range of service po

3.7.2 DMZ DMZ feature allows one local user to be exposed to the Internet for use of a special-purpose service such as Internet gaming or videoconfere

5. Turn on your PC(s). 4

- Enable DDNS: Enable this DDNS function. - Service Provider: Select the DDNS Service Provider. - Domain Name: Enter the Service Provider Domain N

System - Uptime: The date/time shows how long the router power on. - Firmware Version: Show the current firmware version. Wireless Configuration -

- DHCP Server: Shows the DHCP server status. - MAC Address: Shows the MAC address on your LAN port. WAN Configuration - Attain IP Protocol: Shows t

- Current Time: Show the current time of this router. - Time Zone Select: Select the time zone of the country where this router is located. - Ena

name, the password login protection will be disable.) - New Password: Enter the new login password. The passwords can contain 1 to 30 characters and/

- Reset: Click on “Reset” to undo your changes. - Help: To request help information. 3.8.7 Save/Reload Settings You can create a backup file that c

- Apply Changes: Click on “Apply Changes” to confirm to reset this router. - Help: To request help information. 3.9 Event Log This wireless route

47running a syslog daemon. - Apply Changes: Click on “Apply Changes” to save the setting. - Refresh: Get the log data again. - Clear: Click on “Cl

48Appendix A: Troubleshooting Symptom Possible Causes Things to Do • Incorrect or incompatible wireless network configuration. For example, shared

49• Cable failure • Check the “Link” LED. Make sure that your Ethernet cables connect properly. • AP/Router is not power on • Check the “Power” L

2 Preparing Your Network Preparing Your Network In this chapter, you’ll learn what to do before configuring your router. Before you can configure your

50outdated wireless network adapter driver • On a laptop computer, the wireless radio button might be in the off position • With the Services snap

Appendix B: Frequently Asked Questions Q1: What is wireless networking? Ans: The term wireless networking refers to technology that enables two or m

Figure A2: Hardware Access Point. Wireless connected computers using a Hardware Access Point. Figure A3: Software Access Point. Wireless connecte

also allow considerable flexibility in providing access to different network types, such as different types of Ethernet, Wireless and Token Ring netwo

3. Click the IP Address tab. Select Obtain an IP address automatically 4. Now click the Gateway tab, and verify that the Installed Gateway field i

2. Select the Local Area Connection icon for the applicable Ethernet adapter (usually it is the first Local Area Connection listed). Double-click the

5. Restart your computer. The following instructions assume you are running Windows XP with the default interface. If you are using the Classic in

3. Make sure the box next to Internet Protocol (TCP/IP) is checked. Highlight Internet Protocol (TCP/IP), and click the Properties button. 9